HEAT PUMP GUIDE — UPDATED 16 NOVEMBER 2026
Air Source Heat Pumps UK: The Complete Guide for Homeowners
By Phil Handsaker, Government Accredited Domestic Energy Assessor · Updated 16 November 2026
The short answer
A heat pump can be a good long-term heating upgrade, but only for the right home, the right budget and the right installer. On today's price cap rates it is roughly cost-neutral against a gas boiler on a standard tariff, and clearly cheaper only if the system is well designed and you use a cheaper-rate electricity tariff. It is not a quick fix for this winter's bills.
Most heat pump content is written by people who sell heat pumps. This guide is written by an EPC assessor who inspects homes for a living and has nothing to install. That means it covers the awkward questions as well as the usual ones: what goes wrong, what servicing really involves, who should walk away, and what to do instead.
In this guide
- 1. What a heat pump actually is
- 2. What it really costs to run
- 3. Heat pump vs gas boiler
- 4. Heat pump vs infrared heating
- 5. Can your home actually benefit?
- 6. Heat pumps and your EPC rating
- 7. Cost, grants and funding
- 8. The questions nobody asks
- 9. The upsides and the downsides
- 10. Servicing: the part installers rarely lead with
- 11. Not ready for a heat pump? Start saving now
- 12. FAQ
1. What a heat pump actually is
An air source heat pump moves heat from the outside air into your home using electricity, much like a fridge in reverse. Because it moves heat rather than creating it, it can deliver around three units of heat for every one unit of electricity it uses. That ratio is called the seasonal performance factor (SPF), and it is the single most important number in this whole subject.
There are two main types:
Air-to-water heat pumps: Heat your radiators, underfloor heating and hot water cylinder. This is the type most people mean, and the one that replaces a boiler.
Air-to-air heat pumps: Blow warm (or, in summer, cool) air from wall units. They don't heat water or feed radiators, so they suit homes that want to add heating and cooling without a full system change. They are now eligible for a smaller government grant.
A heat pump runs at a lower flow temperature than a boiler (typically 35 to 50°C rather than 60 to 75°C), so it runs for longer, more gently, rather than blasting on and off. That is why the building matters as much as the machine.
2. What it really costs to run
The honest answer is "it depends on three things": the efficiency of your system (SPF), the price of electricity, and how much heat your home loses.
Under the Ofgem price cap from 1 October to 31 December 2026, a typical household on a standard tariff pays about 26.32p per kWh for electricity and 7.97p per kWh for gas. Electricity is roughly 3.3 times the price of gas, which is exactly why heat pumps are not an automatic win. They need to be about three times more efficient than gas just to break even.
Cost per kWh of heat delivered
| Heating type | Efficiency | Approx. cost per kWh |
|---|---|---|
| Gas boiler | ~85% | ~9.4p |
| Heat pump (poor install, SPF 2.5) | 250% | ~10.5p |
| Heat pump (typical, SPF 3.0) | 300% | ~8.8p |
| Heat pump (excellent, SPF 3.5) | 350% | ~7.5p |
| Electric panels / infrared / direct electric | 100% | ~26.3p |
Illustrative annual fuel cost (8,000 kWh useful heat)
| Option | Approx. annual fuel cost |
|---|---|
| Gas boiler | ~£750 |
| Heat pump, SPF 2.5 | ~£840 |
| Heat pump, SPF 3.0 | ~£700 |
| Heat pump, SPF 3.5 | ~£600 |
| Heat pump SPF 3.0 on a cheaper blended rate of about 20p/kWh | ~£530 |
| Direct electric heating | ~£2,100 |
Cold weather performance at -3°C
Heat pump efficiency falls as the outdoor temperature drops, and the flow temperature your radiators need is the biggest lever. At around -3°C, indicative figures look like this:
| Flow temperature | Typical COP | Cost per kWh | vs gas (~9.4p) |
|---|---|---|---|
| 35°C (underfloor, large radiators) | ~3.0 | ~8.8p | Cheaper |
| 45°C (modern or upsized radiators) | ~2.5 | ~10.5p | ~12% dearer |
| 55°C (older radiators left as they are) | ~2.0 | ~13.2p | ~40% dearer |
A heat pump only drops to 1:1 (the same as a fan heater, about 26p per kWh) if it reaches its minimum operating temperature, often somewhere around -15°C to -25°C, or when the backup electric heater runs. Both are rare in the UK.
These figures are illustrations using price cap averages, not a quote or a guarantee. Rates vary by region, tariff and supplier, and the next price cap (from 1 January 2027) is due to be announced by 25 November.
3. Heat pump vs gas boiler
| Aspect | Gas boiler | Air source heat pump |
|---|---|---|
| Upfront cost | Lower (often £2,000 to £4,000 installed) | Higher (typically £10,000 to £15,000 before grant) |
| Grant | None | £7,500 in England and Wales |
| Running cost on standard tariff | Baseline | Similar to modestly lower, if well designed |
| Running cost on a cheap-rate tariff | Unchanged | Can be meaningfully lower |
| Carbon emissions | Higher | Much lower, and falling as the grid decarbonises |
| Space needed | Small wall-hung unit | Outdoor unit plus an indoor hot water cylinder |
| Servicing | Around £79 a year on average, engineers everywhere | About £150 to £300 a year, fewer engineers |
| Typical lifespan | Around 10 to 15 years | Commonly quoted at 15 to 25 years with servicing |
| Spare parts | Cheap, stocked locally almost everywhere | Dearer and less often on the shelf, but parts fail less often |
| Future-proofing | Gas heating faces long-term policy pressure | Aligned with where policy is heading |
The fair summary: a gas boiler is cheaper to buy and simpler. A heat pump is more expensive up front, is better aligned with the long-term direction of travel, and only pays off financially when the install is designed well and the tariff suits.
4. Heat pump vs infrared heating
This is the comparison almost nobody writes fairly. Heat pump installers tend to dismiss infrared. Infrared sellers tend to promise miracles. Both are partly right.
Far infrared panels heat objects and people directly rather than warming the air, which means a room can feel comfortable at a lower air temperature. That is a real effect. But the electricity they use is still direct electric at 26.32p per kWh, which makes them roughly three times more expensive to run per unit of heat than a well-designed heat pump.
Where infrared makes sense: a workshop, a garden room, a bathroom, or a space used occasionally where you want instant warmth without heating the whole building. Where it does not: as the primary heating for a whole home on a standard tariff.
5. Can your home actually benefit?
A heat pump works best in a home that does not lose heat too quickly, because the system runs at a lower flow temperature and needs time to do its job. The better your insulation, the lower the flow temperature you need, and the more efficient the system.
Good candidates: homes with loft insulation, cavity or solid wall insulation, double or triple glazing, and either underfloor heating or radiators that can be upsized. Detached and semi-detached houses with outdoor space for the unit.
Harder cases: flats (freeholder permission, no outdoor space, no cylinder room), listed buildings (planning restrictions), homes with very poor insulation where the fabric work needed first is substantial, and homes where the electrical supply needs upgrading.
A proper heat loss survey — not a rule of thumb — is the only way to know for your specific home. Any installer who quotes without one is guessing.
6. Heat pumps and your EPC rating
A well-installed heat pump should improve your EPC rating, but the size of the improvement depends on the assessor having the right evidence. An assessor can use a heat pump's listed performance figures when they can identify the exact model from the MCS certificate and commissioning sheet. Without that, they fall back on cautious defaults, which can drag the rating down.
Keep your MCS certificate and commissioning sheet and hand them to your assessor before the EPC is lodged. If the rating looks wrong, ask them to review it.
The new multi-metric EPC is currently expected in the second half of 2027. Under the new system, a heat pump is expected to score well on the heating metric, which is one of the two metrics landlords will need to pass for Band C. See our EPC 2030 landlord guide for the full picture.
7. Cost, grants and funding
The Boiler Upgrade Scheme (BUS) is the main government grant for heat pumps in England and Wales.
- £7,500 towards an air-to-water heat pump
- £9,000 towards an oil or LPG home (temporary uplift to 31 March 2027)
- £2,500 towards an air-to-air heat pump (introduced in 2026)
- Your MCS-certified installer applies for you and takes the grant off the bill
- Since April 2026 you no longer need a valid EPC to apply
- Hybrid systems that keep the gas boiler don't qualify
- Scotland has a separate scheme through Home Energy Scotland
Grants can change, so confirm the current amount with an MCS installer and on the official Ofgem and GOV.UK pages before you commit.
Outlay vs payback: illustrative scenarios
| Scenario | Extra outlay after grant | Net annual saving | Rough payback |
|---|---|---|---|
| Replacing a failed gas boiler, standard tariff | ~£2,350 | About -£70 (£50 running saving, £120 extra servicing) | Not on running costs alone |
| Same, cheaper-rate tariff (~20p blended) and gas fully removed | ~£2,350 | ~£210 (£220 running + £108 standing charge - £120 servicing) | ~11 years |
| Replacing direct electric heating | ~£5,350 | ~£1,200 (£1,400 running - £200 servicing) | ~4 to 5 years |
| Replacing a working gas boiler early | ~£5,350 | -£70 to £210 | 25+ years, or never |
What a good heat pump quote should contain
- A room-by-room heat loss calculation, not a rule of thumb or the size of your old boiler
- The design flow temperature and the seasonal efficiency (SCOP or SPF) it expects at that design
- A radiator schedule: which radiators stay, which change, and why
- The hot water plan: cylinder size and location, or a heat battery if space is tight
- The unit model, its position and a noise assessment (MCS 020a in England)
- MCS certification, with the Boiler Upgrade Scheme grant shown as a deduction the installer applies for
- Controls: weather compensation and sensible schedules
- Servicing cost and warranty terms in writing
- What is not included, such as electrical upgrades, making good and scaffolding
Red flags: a quote with no heat loss calculation, a claim that you won't need any radiator changes without one, a vague efficiency promise, pressure to sign on the day, and an installer who won't give you a servicing price. Get at least two or three quotes and compare them like for like.
8. The questions nobody asks
What happens if it breaks on a freezing night?
Heat pumps are generally reliable, but when something does fail you are dependent on a smaller pool of qualified engineers than gas boilers have. Ask any installer how quickly they respond, whether they offer out-of-hours cover, and what the plan is if the heating is off for several days.
What happens in a power cut?
No electricity means no heating, same as a modern gas boiler (which also needs power for its pump and controls). A heat pump does not run on batteries unless you have a large battery system sized for it.
Will my neighbours hear it?
Modern units are quiet, but they are not silent, and placement matters. A unit next to a bedroom window or against a boundary fence can cause problems. Ask for the manufacturer's noise data and think about where it will sit relative to neighbouring bedrooms.
Is it noisy to live with?
Mostly it is a low, steady hum rather than a loud noise, and in most settings you will barely notice it over traffic, wind and everyday sound. In very quiet places it stands out more. If you live somewhere very quiet, or you are sensitive to steady low-frequency sound, ask to hear a running unit of the same model on a cold day.
Why is it blowing steam?
In cold, damp weather the outdoor unit periodically goes into a defrost cycle, which can release a cloud of vapour and may briefly use extra energy. This is normal behaviour, not a fault.
Will it feel different?
Yes. Radiators feel warm rather than hot, and the house is heated steadily rather than in blasts. Many people prefer the constant comfort. Others who are used to blasting the heating for an hour then turning it off find it takes some adjusting to.
Do I need to change how I use my heating?
Usually, yes. Heat pumps work best left on at a steady lower temperature, with sensible schedules, rather than turned fully off and back on. Poor controls and settings are one of the most common reasons systems underperform.
What about hot water?
You'll need a cylinder. The system also needs to heat that water to a higher temperature periodically for hygiene, which costs more energy than normal running. A good install handles this efficiently, a poor one doesn't.
What if there's no room for a cylinder?
In a small home this is the usual sticking point. A heat battery such as the Sunamp Thermino stores heat in a much more compact unit than a standard cylinder and can be charged from surplus solar or cheaper-rate electricity. Check that it is sized for your household's hot water use.
Can I still use my gas hob?
Yes, if you keep a gas connection. If you fully remove gas to save the standing charge, you'll need to switch cooking to electric. Check the full cost before deciding.
9. The upsides and the downsides
Upsides
- Lower carbon emissions, and falling further as the electricity grid decarbonises.
- Longer lifespan than a gas boiler: 15 to 25 years is commonly quoted with proper servicing.
- Aligned with where energy policy is heading, including EPC reform and the 2030 landlord deadline.
- Can be meaningfully cheaper to run than gas on a suitable time-of-use electricity tariff.
- Removes the gas standing charge if you fully disconnect (roughly £108 a year at current cap rates).
- Steady, comfortable heat rather than blasts of hot air.
- Can also cool in summer if paired with an air-to-air unit or a reversible system.
Downsides
- High upfront cost: typically £10,000 to £15,000 before the £7,500 grant.
- On a standard tariff, the running cost saving over gas is modest, not transformational.
- Needs space: an outdoor unit and, for air-to-water systems, an indoor hot water cylinder.
- Servicing costs more than a gas boiler: typically £150 to £300 a year versus around £79.
- Spare parts cost more and there are fewer engineers, though parts fail less often.
- Cold weather reduces efficiency. Heat pumps still work well in UK winters, but they use more electricity on the coldest days.
- Policy and prices can change. Grants, rules and tariffs are not fixed.
10. Servicing: the part installers rarely lead with
Installers earn most of their money on the installation, so servicing tends to get a lighter mention. Here is what to ask about before you sign.
An annual service for an air source heat pump typically costs about £150 to £300, with around £200 common. By comparison, an annual gas boiler service has averaged around £79 according to Which?.
Servicing options and typical prices (2026)
| Service | Typical cost | Usually included |
|---|---|---|
| Basic air source service | £150 to £200 | Visual inspection, filter cleaning, pressure and refrigerant checks |
| Full air source service | £200 to £300 | The above plus electrical testing, flow temperature checks and a performance report |
| Manufacturer-direct service | From about £250 | Brand inspection, often including VAT |
| Monthly care plan | £10 to £25 a month | The annual service, sometimes with priority call-outs or parts cover |
Most manufacturers require evidence of annual servicing to keep the warranty valid. Some standard warranties run for five to seven years, with longer cover offered if the unit is registered and serviced every year. Always read the exact terms.
Spare parts: indicative costs
| Part | Typical cost |
|---|---|
| Sensors (thermistors), pressure relief valves, seal kits | £15 to £65 |
| Circuit board (PCB), DC fan motor or soft starter | £140 to £560 |
| Compressor, fitted | £1,000+ |
| Pumps, zone valves, expansion vessels, magnetic filters | Same as on a boiler system |
Questions to ask before buying
- 1What does your annual service cost, in writing?
- 2Is servicing a condition of the warranty, and for how long?
- 3Do you offer a service plan, and what does it include?
- 4How quickly do you attend breakdowns, including in winter?
- 5What happens if you stop trading? Is there any insurance-backed or manufacturer-backed cover?
If you read that list and feel uneasy about long-term costs, that is a legitimate reason to wait, not a failure of nerve.
11. Not ready for a heat pump? Start saving now
Most people reading a guide like this are not about to spend £10,000. They are worried about bills, curious about the tech, and want to know what they can do without a big gamble. That is the most sensible group of all, and there is plenty you can do right now.
Low-cost moves that work whatever heating you have
- 1
Fix the cheap heat losses first. Draught-proof doors and windows, close up gaps, use a chimney balloon on unused chimneys, and add loft insulation if it is thin. These are the cheapest kWh you will ever save.
- 2
Tune your heating. Lower your boiler flow temperature if your boiler allows it (many run hotter than they need to), use thermostatic valves, and set sensible schedules. Don't heat empty rooms.
- 3
Look at your EPC. Your certificate lists recommendations in order of cost and benefit. If it's old, it may be worth a fresh look.
- 4
Know your numbers. Check how much you actually use with our home energy audit calculator before anyone sells you anything.
- 5
Check your tariff. This is the biggest single lever that costs nothing, and it is where the next section comes in.
The price cap has risen in recent quarters, and forecasters expect further movement from January. Many households are on the default tariff simply because switching feels like effort. Whatever heating you have today, or plan to have, the price you pay per unit sits underneath every calculation in this guide.
Utility Warehouse (UW) supplies energy, broadband, mobile SIMs and home insurance (including boiler insurance) from one account, and bundling services is how it aims to lower the overall cost. For a household that isn't ready for a heat pump, or is deciding what to do over the next few years, it offers three practical benefits: no new equipment and no upfront cost; it works with the heating you already have; and it can be done in an evening.
Check what UW could save you →Energy Guardian is an independent advice site. As a UW partner I may earn a referral fee if you sign up through links on this page, at no extra cost to you. Savings depend on your usage, region and current tariff, and are never guaranteed. Compare before you decide.
12. FAQ
Are air source heat pumps worth it?
For the right home, owned long term, with decent insulation and a well-designed system, they can be a strong investment, especially with the grant and a suitable tariff. For others the payback is slow or uncertain.
Are heat pumps cheaper to run than gas?
Not automatically. At current price cap rates, a typical heat pump is roughly in line with gas, and cheaper if the system performs well and you use a lower electricity rate.
How much is the heat pump grant?
£7,500 for most homes in England and Wales, £9,000 for oil or LPG homes under the temporary uplift to 31 March 2027, and £2,500 for air-to-air systems. Always confirm current amounts with an installer and on GOV.UK.
Do heat pumps work in cold weather?
Yes. They work well in UK winters, though efficiency dips as temperatures fall.
Do heat pumps work in older houses?
Often, yes, but older homes usually need more fabric and radiator work to get good results. A proper heat loss survey comes first.
How much does it cost to service a heat pump?
Typically £150 to £300 a year for an air source system, and servicing is usually a condition of the warranty.
Is infrared heating cheaper than a heat pump?
It is cheaper to buy but far more expensive to run per unit of heat. It works best for small, occasionally used spaces.
I'm renting. Can I get a heat pump?
Usually not by yourself, because it needs your landlord's agreement. Focus on tariff, draught-proofing and efficient use of what you have.
What should I do if I can't afford one?
Start with the cheapest wins: draughts, insulation, controls and your tariff. Heat pumps will still be there when the numbers make sense for you.
Can I fit a heat pump in a flat or leasehold property?
Sometimes, but it is harder. You usually need the freeholder's permission, somewhere to put the outdoor unit and, for an air-to-water system, space for a cylinder. If a heat pump isn't practical, there are electric options that need no outdoor unit, such as heat batteries, high heat retention storage heaters and infrared panels.
Do I need planning permission for a heat pump?
In England, most air source heat pumps on houses are permitted development, so you don't need to apply. Since 29 May 2025 the one-metre boundary rule has gone, units can be up to 1.5 m³, and detached houses can have two. The key condition is noise: an MCS 020a assessment must show the unit stays within 42 dB(A) at the nearest neighbouring home. Scotland, Wales and Northern Ireland have their own rules.
Should I add solar panels and a battery?
They can help, but they won't remove your winter heating bills. Solar generation is lowest when heating demand is highest, so the main benefit is in spring and autumn, and for hot water in summer. Treat solar and a battery as a separate investment that happens to fit well, not a requirement.
Will a heat pump affect my mortgage, insurance or resale value?
Tell your home insurer when you fit one. Evidence on resale value is still developing. Keep the MCS certificate, commissioning report, warranty and service records together, because a buyer or surveyor will ask for them.
Will my EPC show the heat pump properly?
It should, but evidence matters. An assessor can use a heat pump's listed performance figures when they can identify the exact model, and has to fall back on cautious defaults when they can't. Keep your MCS certificate and commissioning sheet and hand them to your assessor.
Sources
- Ofgem: energy price cap, 1 October to 31 December 2026
- Energy Saving Trust: Boiler Upgrade Scheme
- GOV.UK: approved grant categories and values
- Energy Saving Trust: infrared heating explained
- Elmhurst Energy: Horizons 2026 (EPC reform and the Home Energy Model)
This guide is general information, not a quotation, a survey or financial advice. Figures use Ofgem price cap rates for 1 October to 31 December 2026 and publicly available grant and servicing information at the time of writing, and will change. Always obtain written quotes from MCS-certified installers before committing.